series am er90 c -c az up to 3.75a | ac- dc / dc - dc | led dri ver / converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3 .b 1 of 6 north america only features: models single output model max output power (w) output voltage range (v) output current (a) input voltage (vac/hz) input voltage (vdc) mode of operation efficiency (%) 115 vac 230 vac 277 vac amer90 c - 50180c az 90 36-50 1.8 90- 305/47- 440 130 - 430 constant current 87 86 86 constant volt age 88 87 87 amer90 c - 36250c az 90 24-36 2.5 90- 305/47- 440 130 - 430 constant current 87 87 87 constant voltage 88 87 87 amer90 c - 24375c az 90 12-24 3.75 90- 305/47- 440 130 - 430 constant current 86 86 86 constant voltage 87 86 86 exceeding the maximum output power will permanently damage the converter . the dimming feature is not supported when units are used in constant voltage mode only, in constant current mode output current is maximum shown, in constant voltage mode output voltage is th e maximum shown. all models can be ordered with optional north american colour input wires ( black (l) , white (n) , green (gnd)) . add C na to part number when ordering. note: aimtec limited warranty of 5 years is valid based on product operation at datas heet specifications at ambient temperature of 25c, humidity<75%, nominal input voltage (115/230/277vac) and at rated output load unless otherwise specified. see http://www.aimtec.com/terms - sale amer90c - caz s ac/dc led drivers have electrical safeguards designed within to protect it from conventional electrical abnormalities with the levels listed in the safety table. applications for use within rural agricultural, heavy industrial, and other areas or region s which are prone to dirty electrical conditions which would subject any of the above models to excessive voltages surges or spikes, ma y damage or cause early life failure of product. in this case consideration should be made by the end user to ensure th at adequate line or mains surge suppression is installed in front of aimtec device to ensure the longevity of the products. failure to identify excessive li ne surges violations prior to installation may damage sensitive equipment permanently. input speci fications parameters conditions typical maximum units current (full load) 115 vac 1500 ma 230 vac 600 ma 277 vac 500 ma inrush current <2ms(cold start) 115 vac 40 a 230 vac 50 a 277 vac 60 a leakage current i/o 0. 2 5 ma i/fg, o/fg 3.5 ma power f actor 115 vac 0.98 230 vac 0.94 277 vac 0.90 external fuse recommended slow blow type 2.5 a start - up time 10 00 ms ? constant current led driver or converter ? over temperature protection ? input range 90 - 305 vac/47 - 440hz ? waterproof case rated ip6 8 ? high efficiency up to 91 % ? power factor correction ? 115vac operating temperature - 5 0 to 8 5 c ? 230 vac operating temp erature - 55 to 85 c ? dimmable via resistive / 0 - 10vdc / pwm ? 5 years limited warranty ? s hort c ircuit p rotection ? over current protection click on series name for product info on aimtec.com
series am er90 c -c az up to 3.75a | ac- dc / dc - dc | led dri ver / converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3 .b 2 of 6 north america only output specifications parameters conditions typical maximum units current accuracy 3 % line regulation ( ll - hl ) 2 % load regulation 0 - 100% load 3 % ripple & noise * 1 5 0 mv p - p hold - up time 100 ms current adjustment range 100 - 1 0 % ripple and noise are measured at 20mhz bandwidth by using a 0.1f (m/c) or (c/c) and 47f (e/c) parallel capacitor. isolation specifications parameters conditions typical rated units tested voltage i/o 3sec 3750 vac i/fg 2000 vac o/fg 500 vac isolation r esistance 500vdc >1000 m general specifications parameters conditions typical maximum units switching frequency 125 khz over current protection R 105 % over voltage protection R 105 % short circuit protection continuous short cir cuit restart auto recovery over temperature protection >105c operating temperature (see derating table) (115vac) - 5 0 to +85 o c (230vac) - 55 to +85 o c cold start - up time - 55c 35 sec maximum case temperature 100 o c storage temperature - 55 to +95 o c temperature coefficient 0.02 % / o c cooling free air convection humidity 95 % rh case material aluminum potting epoxy (ip68 rated) wires ul1015 18awg input & 14awg output *20cm weight 9 00 g dimensions (l x h x w) 7.13 x 2.32 x 1.85 in ches 181.00 x 59.00 x 47.00 mm mtbf >400,000 hrs (mil - hdbk - 217f at +25c) safety specifications parameters agency approvals ce standards en55022, class b, en60529(ip68), en61347 - 1, en61347 - 2 - 13 note: also designed to meet culus, ul8750, ul6095 0 - 1
series am er90 c -c az up to 3.75a | ac- dc / dc - dc | led dri ver / converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3 .b 3 of 6 north america only di mensions 59 . 00 ( 2 . 32 ) 181 . 00 ( 7 . 13 ) 47 . 00 ( 1 . 85 ) 200 . 00 ( 8 . 00 ) 200 . 00 ( 8 . 00 ) 2 . 30 ( 0 . 09 ) end view top view side view input / output wires are 18 awg 20 cm 41 . 00 ( 1 . 73 ) 8 . 00 ( 0 . 32 ) 11 . 00 ( 0 . 43 ) 4 . 00 ( 0 . 16 ) 23 . 00 ( 0 . 91 ) measurements in millimeters ( inch ) case tolerance : 0 . 5 ( 0 . 02 ) 27 . 00 ( 1 . 06 ) temperature graph - 40 - 20 0 20 40 60 80 100 100 80 60 40 20 0 free air convection 55 o c safe operating area ambient temperature o c 85
series am er90 c -c az up to 3.75a | ac- dc / dc - dc | led dri ver / converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3 .b 4 of 6 north america only dimming performance amer90c - 24375c az
series am er90 c -c az up to 3.75a | ac- dc / dc - dc | led dri ver / converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3 .b 5 of 6 north america only amer90c - 36250 c az
series am er90 c -c az up to 3.75a | ac- dc / dc - dc | led dri ver / converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3 .b 6 of 6 north america only amepr90c -50180c az note: 1. datasheets are updated as needed and as such, specifications are subject to change without notice. once printed or downloaded, datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agenc y certifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited inform ation are considered proprietary and may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control s ystems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. warranty is in accordance with aimtecs standard terms of sale available at www.aimtec.com.
|
